Code Alarm CA 671 Manuel d'utilisateur

1CA 671 Installation InstructionsAvoid mounting components or routing wires nearhot surfacesAvoid mounting components or routing wires nearmoving par

10Negative Door Input (GREEN)Locate the vehicle’s dome light or door pin switch wire.Verification: This wire will register ground (NEG) when the doo

Hood Pin Input (GRAY)Install a Hood Pin Switch and connect to the GRAY wire. This connection is required for Remote Start.Verification: This wire when

Parking Light Output (+/-) (WHITE)Locate the vehicle’s parking light wire at the vehicle light switch.Verification: This wire will register positive v

13SONGBIRD (BROWN/WHITE) Speaker Accessory requiredThis wire controls the Speaker accessory (Not Included)Connect this wire to one of the WHITE/BLACK

14Parking Brake Input (GRAY/RED)NOTE: The following connection is only required for Turbo Timer.Verification: This wire will register ground when the

153. 6 PIN REMOTE START HARNESSBattery Power 1 (12 AWG) (RED)Locate the vehicle battery wire(s) at the ignition switch.Verification: These wires wil

16Active Output (18 AWG) (BLUE/BLACK)The Active Output/Ignition 3 output wire provides a ground output when the remote start function is activatedand

17Pulse Before Start (20 AWG) (LIGHT GREEN/BLACK) 500mA OutputLocate the factory perimeter alarm disarm wire from the key cylinder inside the drivers

18AUX 1 (VIOLET/BLACK)This wire provides a 500mA negative output capable of driving relays. For Control of optional accessories(i.e. Power Window/Sunr

19Negative Lock Output / Positive Unlock Output (GREEN)Negative Unlock Output / Positive Lock Output (BLUE)Negative Second Door Unlock Output (BLUE/G

2SAFETYCONTROLSWITCH34Lt BLUE/GREENBLUEUNLOCK SENSE INPUTTRUNK PIN INPUT(-)567891011121314151617181920BLUE/WHITEWHITE/BLUEGRAYGRAY/REDGREENBLACKBROWNW

206. DOOR LOCKSNegative Lock Output / Positive Unlock Output (GREEN)Negative Unlock Output / Positive Lock Output (BLUE)Negative Second Door Unlock

21Negative Lock Output / Positive Unlock Output (GREEN)Negative Unlock Output / Positive Lock Output (BLUE)Negative Second Door Unlock Output (BLUE/G

226. DOOR LOCKSNegative Lock Output / Positive Unlock Output (GREEN)Negative Unlock Output / Positive Lock Output (BLUE)Negative Second Door Unlock

23Negative Lock Output / Positive Unlock Output (GREEN)Negative Unlock Output / Positive Lock Output (BLUE)Negative Second Door Unlock Output (BLUE/G

246. DOOR LOCKSNegative Lock Output / Positive Unlock Output (GREEN)Negative Unlock Output / Positive Lock Output (BLUE)Negative Second Door Unlock

252 Pin Transponder Control Output: (Yellow Connector)This output is intended to allow the control of a transponder bypass interface module or transpo

269. SYSTEM TESTING1. Follow each instruction below.2. Verify that the system operates as indicated under each instruction. Refer to the system owner

27Press DISARM1. Doors unlock2. Factory alarm (if equipped) is turned off.3. Siren/horn sounds once/ parking lights flash once.4. Courtesy lights turn

2810. FINISHING THE INSTALLATION1. Mount the module to a brace or wire harness under the dash. The module and harnesses must be clear ofmoving parts.

29

3CA 671 System Layout4-Pin Tracking Port(White)4-Pin Receiver Port(Black)4-Pin Shock Sensor Port(Tan)4-Pin Auxilliary Port(Green])2-Pin LED Port(White

30

4Programming OptionsRF ProgrammerThe RF Programmer allows you to customize the system to fit the individual needs of the consumer,using a hand held de

5Selecting Programmable Features1. Press the POWER button to turn the system ON.2. Once powered up the MENU screen will be displayed.3. Use the UP

6CA 671 - Programming GuideFeature Bank 1 - 3 Chirps Transmitter ProgrammingFeature Bank 2 - 4 Chirps RF Programmer Receive BankFeature Bank 3 - 5 Chi

7SETUP & PROGRAMMINGTransmitter Programming (3 Chirps)1. Turn the ignition ON.2. Press and hold the valet/override button.3. Within 10 seconds

8Programming Tach RateThe unit will not operate unless tach is programmed or tachless option is turned ON. If an attempt is madeto start the vehicle

9(+)(-)Positive Polarity Output(+)(-)Negative Polarity Output2. BASIC INSTALLATION - 22 PIN BASE HARNESSStarter Input (Key Side) (GREEN) / Starte