Code Alarm PC 7400 Spécifications télécharger pdf (Page 19)

• Multiple Keypad Use: One keypad only must be used on the

option bus, at any address from 11 - 14, and must meet the

following requirements:

- The keypad must be mounted to the front of the control

enclosure OR mounted within the same room as the control

equipment. The wire is run in conduit (or equivalently protected

against mechanical injury) within 20 ft. (6.1m) of the control

equipment.

- All other keypads should be connected to the keypad bus and

may be placed as needed (within the noted wiring limitations in

the installation manual).

- One keypad must be assigned as address 1.

6.12 Open/Close Report Control Programming

• Open and Close Reports: If programmed, these reports are

sent when the system is armed or disarmed. They may be sent

independently for the opening and closing of each partition, or

the first partition to open and the last partition to close may send

the reports.

• Alternate between both Phone Numbers: If programmed, open

and close reports will be sent to phone number one first. If phone

number one does not pick-up, the control panel will alternate to

phone number two. If phone number two does not pick-up, the

control panel will alternate back to phone number one. It will

alternate between both phone numbers until successful.

6.13 Report Programming

• Reports: For pulse formats, reports are programmed by entering

data in the reporting and extended digits. The report will send the

data programmed for each event. For SIA and Contact ID, the

report formats are fixed and may be activated by placing a 1 in

the reporting digit.

- To disable a report, enter a 0 in the reporting digit.

- To send the Man No. along with Open and Close reports,

program an "F" (enter [*] [5] at the keypad) in the extended

digit.

• Keypad Fire Alarm: This report is sent when a fire alarm has

been activated by the “A” emergency key.

• Keypad Fire Restoral: This report is sent when a keypad fire

alarm has been restored using the [System Reset] command.

• Keypad Emergency Alarm: This report is sent when an

emergency alarm has been activated using the “B” emergency

key.

• Keypad Panic: This report is sent when an emergency alarm

has been activated using the “C” emergency key.

• Keypad Tamper: For keypads fitted with a wall tamper switch,

this report is sent when the keypad is removed from the wall.

• Keypad Tamper Restoral: For keypads fitted with a wall tamper

switch, this report is sent when the keypad is properly replaced

on the wall after experiencing a tamper condition.

• Zone Function Alarm: An alarm report is sent when a zone

alarm occurs. Alarm reports are enabled by zone function. Program

this report for any zone functions you wish to send an alarm report

about. For local zones (no reports), do not program an alarm

report. The zone number will automatically be sent for this report

in SIA or Contact ID format.

• Zone Function Restoral: This report is sent when the zone alarm

is cleared. The zone number will automatically be sent for this

report in SIA or Contact ID format.

• Zone Function Trouble: This report is sent when a zone trouble

condition occurs. This can be an open circuit, if the zone is

programmed for “trouble on open”, a multiplex tamper switch being

activated, or a multiplex zone not communicating with the control

panel. The zone number will automatically be sent for this report

in SIA or Contact ID format.

• Zone Function Trouble Restoral: This report is sent when the

trouble condition is cleared. The zone number will automatically

be sent for this report in SIA or Contact ID format.

• Zone Function Bypass: This report is sent when a zone is

bypassed. (Note: Fire zones can never be bypassed.) Zone bypass

reports for non-24 hour zones are sent with the closing report.

Bypass reports for 24 hour zones are sent when the zone is

bypassed. If a zone is force armed, the bypass report is sent with

the partial close report. If a 24 hour or non-24 hour zone is custom

armed, the bypass report is sent with the partial close report.

• Zone Function Bypass Restoral: This report is sent when the

zone bypass is cleared. For non-24 hour zones the bypass restoral

is sent with the open report. Bypass restoral reports for 24 hour

zones are sent when the zone is manually restored. The bypass

restoral report for a zone that was force armed is sent when the

zone is restored. If a 24 hour or non-24 hour zone was custom

armed, the bypass restoral is sent with the open report.

• Open: This report is sent when the system has been disarmed.

In SIA or Contact ID formats, the user number for the person who

disarmed the system will be sent with this report. To send the

user number along with an Open report in other formats, program

the extended digit of the report as *5. In Contact ID format, the

partition number will also be sent along with this report. The Open

report will only be sent if a Close report was sent previously.

• Close: This report is sent when the system has been armed. In

SIA or Contact ID formats, the user number for the person who

armed the system will be sent with this report. To send the user

number along with a Close report in other formats, program the

extended digit of the report as *5. In Contact ID format, the partition

number will also be sent along with this report.

• Duress: This report is sent when the system is disarmed using a

duress code. The user number is not sent with this report.

• Partial Close: This report is sent when the system is armed

partially, or force armed.

• First Open After Alarm: This report is sent when the system is

disarmed after an alarm has occurred.

• Low Battery: This report is sent when a low battery condition

occurs.

• Battery Restoral: This report is sent when a low battery condition

restores.

• AC Fail: This report is sent when an AC failure condition occurs.

This report may be delayed in address 0197.

• AC Failure Report Delay

The AC power loss report can be programmed to delay for up to

254 minutes (see address 0197). (The same delay would also

apply to the AC restoral report.)

- If another report is sent during this delay period, the AC fail

report will be sent along with this report.

- If the AC power restores during this delay period, the AC loss

report will not be sent.

- Programming address 0197 as FF causes the report to be sent

at a random interval of at least 15 minutes, but no more than 2

hours after the AC failure occurs.

• AC Restoral: This report is sent when an AC failure condition

restores.

• Communicator Test/System Normal: This report is sent at the

1 2 ... 14 15 16 17 18 19 20 21 22 23 24 ... 91 92

Commentaires sur ces manuels

Pas de commentaire

Code Alarm PC 7400 Spécifications Page 19

Commentaires sur ces manuels

Produits connexes et manuels pour Les démarreurs à distance Code Alarm PC 7400